Archive for

In the winter, you want to make sure your oil furnace keeps your home warm and your family comfortable. Homeowners experience short-cycling or overheating complications with their furnaces. With short cycling, the oil furnace turns on plus off frequently. Periodically it will not make any heat at all before shutting down, and common reasons your oil furnace may be short cycling include overheating, bad flame sensor, dirty oil furnace filter, clogged exhaust vent or heat grates, improper temperature control placement, or having a oil furnace that is too big for your home. Your oil furnace may turn off prematurely if it is overheating, almost immediately after lighting, the oil furnace flame will go out if the flame sensor or flame rod is bad. Your oil furnace can short cycle and overheat if it has a dirty filter. You may notice that your furnace shuts off only a few minutes before your home is warm, overheating can also be caused by clogged heat grates, which don't let enough air out, blocked exhaust vents can also cause overheating plus short cycling, but it is a potentially dangerous reason since carbon monoxide can leak through! The location of your temperature control matters because if your temperature control is getting warmed before the rest of the house, it will cause your oil furnace to turn off prematurely, and most homeowners install the temperature control themselves, it's not unusual for homes to have too big oil furnaces because the installer thought greater was better. This is not true, but, plus can lead to short cycling of your unit. The best solution, if this is the cause of your oil furnace's short cycling, is to replace it, and short cycles, temperature swings, and high heating bills may indicate this is the issue.

How to determine if your HVAC is short cycling   hvac unit

In the winter, you want to make sure your furnace keeps your house hot as well as your family comfortable, homeowners experience short-cycling or overheating concerns with their furnaces, with short cycling, the oil furnace turns on as well as off frequently! Sporadically it will not make any heat at all before shutting down. Common reasons your furnace may be short cycling include overheating, exhausting flame sensor, dirty furnace filter, obstructed exhaust vent or heat grates, improper thermostat sitement, or having a oil furnace that is too big for your home, your oil furnace may turn off prematurely if it is overheating. Almost right away after lighting, the oil furnace flame will go out if the flame sensor or flame rod is bad. Your furnace can short cycle as well as overheat if it has a dirty filter. You may notice that your oil furnace shuts off only a few hours before your beach house is warm, overheating can also be caused by obstructed heat grates, which don't let enough air out. Blocked exhaust vents can also cause overheating as well as short cycling, but it is a potentially dangerous reason since carbon monoxide can leak through. The location of your thermostat matters because if your thermostat is getting warmed before the rest of the house, it will cause your oil furnace to turn off prematurely. Most homeowners install the thermostat themselves, so it's not unusual for homes to have too big heating systems because the installer thought larger was better. This is not true, however, as well as can lead to short cycling of your unit. The best solution, if this is the cause of your oil furnace's short cycling, is to replace it. Short cycles, temperature swings, as well as high heating bills may indicate this is the issue.

Reasons why your heater might short cycle heating corp

In the winter, you want to make sure your furnace keeps your home warm and your family comfortable, but homeowners experience short-cycling or overheating complications with their furnaces. With short cycling, the furnace turns on and off frequently. Occasionally it will not make any heat at all before shutting down, and common reasons your gas furnace may be short cycling include overheating, bad flame sensor, dirty gas furnace filter, blocked exhaust vent or heat grates, improper control unit placement, or having a gas furnace that is too big for your home. Your gas furnace may turn off prematurely if it is overheating. Almost immediately after lighting, the gas furnace flame will go out if the flame sensor or flame rod is bad. Your gas furnace can short cycle and overheat if it has a dirty filter. You may notice that your gas furnace shuts off only a few hours before your home is warm. Overheating can also be caused by blocked heat grates, which do not let enough air out. Blocked exhaust vents can also cause overheating and short cycling, but it is a potentially dangerous reason since carbon monoxide can leak through! The location of your control unit matters because if your control unit is getting warmed before the rest of the house, it will cause your gas furnace to turn off prematurely. Most homeowners install the control unit themselves. It's not uncommon for homes to have too important furnaces because the installer thought larger was better. This is not true, and can lead to short cycling of your unit. The best solution, if this is the cause of your gas furnace's short cycling, is to substitute it. Short cycles, temperature swings, and high heating bills may indicate this is the issue.

What happens with short cycling   link here

In the winter, you want to make sure your furnace keeps your home warm and your family comfortable. Homeowners experience short-cycling or overheating issues with their furnaces. With short cycling, the furnace turns on and off frequently. Sometimes it won't make any heat at all before shutting down. Common reasons your furnace may be short cycling include overheating, bad flame sensor, dirty furnace filter, blocked exhaust vent or heat grates, improper thermostat placement, or having a furnace that is too big for your home. Your furnace may turn off prematurely if it is overheating. Almost immediately after lighting, the furnace flame will go out if the flame sensor or flame rod is bad. Your furnace can short cycle and overheat if it has a dirty filter. You may notice that your furnace shuts off only a few minutes before your home is warm. Overheating can also be caused by blocked heat grates, which don't let enough air out. Blocked exhaust vents can also cause overheating and short cycling, but it is a potentially dangerous reason since carbon monoxide can leak through. The location of your thermostat matters because if your thermostat is getting warmed before the rest of the house, it will cause your furnace to turn off prematurely. Most homeowners install the thermostat themselves. It's not uncommon for homes to have too large furnaces because the installer thought bigger was better. This is not true, however, and can lead to short cycling of your unit. The best solution, if this is the cause of your furnace's short cycling, is to replace it. Short cycles, temperature swings, and high heating bills may indicate this is the issue.

Making sure the furnace keeps your home warm   cooling

The discovery of a dead rat, mouse or small rodent in a home's ductwork is not pleasant for a homeowner, then it often leaves you with an unpleasant stink and a lot of mess to clean up. Although the animal died in your ducts, the smell is likely to seep into your home and cause your entire home to stink. If this occurs in your home, you are wondering where the stink is coming from and how to get rid of it? Even though it's best to have a professional handle this style of situation, there are some things you can do if a small animal dies in your ductwork. Usually, the stink of the decomposing rodent will alert you to the problem, but when you notice a stink, it could mean that an animal died in your basement, attic, crawlspace, or ductwork. However, the only way to discover where it died is to just follow the scent, then remove the animal if it can be seen. If you don't see it instantly, you may need to consider hiring a professional to find a locale to dispose of the animal. When they die, they often crawl into nooks or dark corners, or even into insulation, making it extremely hard to find them, and once found, it will need to be carefully removed. Prepare supplies such as a garbage bag, rubber gloves, paper towels, and disinfectant spray. Following the removal of the animal and cleaning of the area, you should take follow-up action, but you should have a thorough inspection performed of your system and ductwork to determine how the animal entered the system. It's pressing to find them in order to avoid another animal getting into your ductwork, and to increase your system's energy efficiency. You may also want to have your ducts professionally cleaned. As a result, any lingering smells will be removed and you will be assured that there are no bacteria or viruses left behind, even though this is a problem you can actually solve on your own, you can see why it would be helpful and even necessary to hire a professional to assist you.

Is Your Furnace Short Cycling? More about heating

The discovery of a dead rat, mouse or small rodent in a home's ductwork is not pleasant for a homeowner, it often leaves you with an unpleasant smell and a lot of mess to clean up, although the critter died in your ducts, the stink is likely to seep into your home and cause your entire home to smell. If this occurs in your home, you are probably wondering where the smell is coming from and how to get rid of it? Even though it's best to have a professional handle this category of situation, there are some things you can do if a small critter dies in your ductwork, usually the smell of the decomposing critter will alert you to the problem. When you notice a smell, it could mean that a critter died in your basement, attic, crawlspace, or ductwork. The only way to discover where it died is to just follow the scent. Remove the critter if it can be seen. If you don't see it right away, you may need to consider hiring a professional to find a place to dispose of the critter. When critters die, they often crawl into nooks or dark corners, or even into insulation, making it seriously hard to find them. Once found, it will need to be carefully removed, however prepare supplies such as a garbage bag, rubber gloves, paper towels, and disinfectant spray, and following the removal of the critter and cleaning of the area, you should take follow-up action! You should have a thorough inspection performed of your program and ductwork to determine how the critter entered the system. It's important to find them in order to avoid another critter getting into your ductwork, and to increase your system's energy efficiency. You may also want to have your ducts professionally cleaned. As a result, any lingering smells will be removed and you will be assured that there are no bacteria or viruses left behind! Even though this is a concern you can particularly solve on your own, you can see why it would be helpful and even necessary to hire a professional to assist you.

You may want to have your ducts professionally cleaned ductwork cleaning

The discovery of a dead rat, mouse or small rodent in a home's HVAC duct is not pleasant for a homeowner, and it often leaves you with an unpleasant stink and a lot of mess to clean up. Although the animal died in your ducts, the stink is likely to seep into your home and cause your entire home to stink. If this occurs in your home, you are definitely wondering where the stink is coming from and how to get rid of it? Even though it's best to have a professional handle this type of situation, there are some things you can do if a small animal dies in your HVAC duct, usually the stink of the decomposing animal will alert you to the problem, then when you notice a stink, it could mean that an animal died in your basement, attic, crawlspace, or HVAC duct. However, the only way to discover where it died is to just follow the scent. Remove the animal if it can be seen. If you don't see it immediately, you may need to consider hiring a professional to find a locale to dispose of the animal. When animals die, they often crawl into nooks or dark corners, or even into insulation, making it difficult to find them. Once found, it will need to be carefully removed, then prepare supplies such as a garbage bag, rubber gloves, paper towels, and disinfectant spray. Following the removal of the animal and cleaning of the area, you should take follow-up action, and you should have a thorough inspection performed of your plan and HVAC duct to determine how the animal entered the system. It's important to find them in order to avoid another animal getting into your HVAC duct, and to increase your system's energy efficiency. You may also want to have your ducts professionally cleaned. As a result, any lingering smells will be removed and you will be assured that there are no bacteria or viruses left behind. Even though this is a concern you can definitely solve on your own, you can see why it would be helpful and even necessary to hire a professional to assist you.

You may need a professional for dead animal in the ducts ductwork

The discovery of a dead rat, mouse or small rodent in a home's HVAC duct is not pleasant for a homeowner, and it often leaves you with an unpleasant smell and a lot of mess to clean up! Although the critter died in your ducts, the odor is likely to seep into your house and cause your entire house to smell. If this occurs in your home, you are undoubtedly wondering where the smell is coming from and how to get rid of it? Even though it's best to have a professional handle this style of situation, there are some things you can do if a small critter dies in your HVAC duct! Usually, the smell of the decomposing critter will alert you to the problem, when you notice a smell, it could mean that a critter died in your basement, attic, crawlspace, or HVAC duct! However, the only way to discover where it died is to just follow the scent. Remove the critter if it can be seen. If you don't see it immediately, you may need to consider hiring a professional to find a place to dispose of the critter. When critters die, they often crawl into nooks or dark corners, or even into insulation, making it harshly difficult to find them, but once found, it will need to be carefully removed. Prepare supplies such as a garbage bag, rubber gloves, paper towels and disinfectant spray, following the removal of the critter and cleaning of the area, you should take follow-up action! You should have a thorough inspection performed of your idea plus HVAC duct to determine how the critter entered the system. It's important to find them in order to avoid another critter getting into your HVAC duct, as well as to increase your system's energy efficiency. You may also want to have your ducts professionally cleaned. As a result, any lingering odors will be removed and you will be assured that there are no bacteria or viruses left behind, even though this is a problem you can undoubtedly solve on your own, you can see why it would be helpful and even necessary to hire a professional to assist you.

How to dispose of a dead animal found in your ductwork   more information on air conditioning

The discovery of a dead rat, mouse or small rodent in a home's ductwork is not pleasant for a homeowner. It often leaves you with an unpleasant smell and a lot of mess to clean up. Although the animal died in your ducts, the odor is likely to seep into your home and cause your entire house to smell. If this occurs in your home, you are probably wondering where the smell is coming from and how to get rid of it? Even though it's best to have a professional handle this type of situation, there are some things you can do if a small animal dies in your ductwork. Usually, the smell of the decomposing animal will alert you to the problem. When you notice a smell, it could mean that an animal died in your basement, attic, crawlspace, or ductwork. However, the only way to discover where it died is to just follow the scent. Remove the animal if it can be seen. If you don't see it right away, you may need to consider hiring a professional to find a place to dispose of the animal. When animals die, they often crawl into nooks or dark corners, or even into insulation, making it extremely difficult to find them. Once found, it will need to be carefully removed. Prepare supplies such as a garbage bag, rubber gloves, paper towels, and disinfectant spray. Following the removal of the animal and cleaning of the area, you should take follow-up action. You should have a thorough inspection performed of your system and ductwork to determine how the animal entered the system. It's important to find them in order to avoid another animal getting into your ductwork, as well as to increase your system's energy efficiency. You may also want to have your ducts professionally cleaned. As a result, any lingering odors will be removed and you will be assured that there are no bacteria or viruses left behind. Even though this is a problem you can probably solve on your own, you can see why it would be helpful and even necessary to hire a professional to assist you.

What to do if an animal dies in your ductwork energy saving tips

Your house's year-round comfort depends largely on whether your heating and A/C systems are really working officially – meaning they keep your home cool in the summertime and warm in the winter. When it's time to update your heating or cooling system, you may think it's better to simply update the component that has caused you trouble. But what several people do not realize is that replacing both systems at once can really save you both money and energy in the long run, and the first thing to consider when deciding whether you should update your system is how long you've had it, and in general, a gas furnace will last 15-20 years while a central a/c system will last 12-15 years. A look at your utility bills may also indicate it is time to update your a/c unit or gas furnace. This can indicate that your unit is really working overtime and needs to be updated if your bills have significantly increased. An advantage of installing a new gas furnace and a/c system at the same time is that it's more energy efficient! heating and A/C systems nowadays are highly efficient and use much less energy than older systems. It will be easier to ensure a similar performance level between all the units if it is matched, but you can't fully benefit from a new gas furnace if you have an old air conditioner and a brand new gas furnace. As a final note, it may really be more cost-effective to update both the AC and gas furnace at the same time, because proper components might have to be updated twice if they are not updated simultaneously. In other words, you will pay twice for the same material and labor. In addition, if your units are located in hard-to-reach areas, it makes more sense to update them both at the same time, as installation labor is usually higher in these areas.

Rodents in Your Ductwork   heat and ac products